Asbestos management surveys: key facts
- A management survey is the standard survey for premises in normal occupation and use. HSE describes two survey types: management, and refurbishment or demolition.
- It is not a law in itself. The law (regulation 4 of the Control of Asbestos Regulations 2012) requires a suitable and sufficient assessment of whether asbestos is present; HSE says that in most cases this means a management survey by a competent surveyor.
- The inspection goes beyond what you can see. HSE lists ceiling voids, lofts, risers, service ducts, lift shafts, under floor coverings, roofs, soffits, gutters and areas behind access hatches.
- Intrusion is minor. HSG264 says management surveys are only likely to need simple tools such as screwdrivers and chisels.
- HSG264 says default presumption should be avoided where possible: surveyors should try to positively identify asbestos by sampling, which a UKAS-accredited laboratory must analyse.
- Anywhere the surveyor could not get into must be presumed to contain asbestos, listed in the report and managed on that basis until it is checked.
- The surveyor scores each material; you validate the priority. HSE says that even if the report includes a priority assessment, only the dutyholder knows how each area is used.
- It is not enough for building work. HSG264 says a refurbishment survey is needed for any work that disturbs the building fabric where the management survey was not intrusive.
What is an asbestos management survey?
It is the standard asbestos survey described in HSE's guide HSG264. Its purpose is to locate, as far as reasonably practicable, any suspect asbestos-containing materials (ACMs) that could be damaged or disturbed during normal occupancy, including foreseeable maintenance and installation, and to assess their condition.
HSE's survey guide, Asbestos: The survey guide (HSG264, second edition 2012), describes two types of survey: a management survey and a refurbishment or demolition survey. The management survey is the one most non-domestic buildings need first, and the one that supports the ongoing duty to manage asbestos. A refurbishment or demolition survey is a different job for a different purpose: it is carried out before building work and is fully intrusive.
HSE puts the main aim simply: a management survey allows you, as the dutyholder, to produce an asbestos register and an asbestos management plan, and helps you manage asbestos during normal occupation and use of the premises. It is not a search inside the structure: it targets the materials that occupants, maintenance workers and installers could reasonably come into contact with.
A management survey has three parts:
- Finding suspect materials in all reasonably accessible areas, including hidden spaces such as ceiling voids and risers.
- Identifying them, usually by taking samples for laboratory analysis, or by presuming that a material contains asbestos where sampling isn't done.
- Assessing condition: a "material assessment" of how readily each material would release fibres if disturbed.
Old terminology. You may see older reports called a "Type 1", "Type 2" or "Type 3" survey. HSE's survey guide replaced those terms with the management survey and the refurbishment or demolition survey. An older report can still hold useful information, so give it to your surveyor, but don't assume it meets the current guide.
Where this sits in the law: in Great Britain, regulation 4 of the Control of Asbestos Regulations 2012 (CAR 2012) places the duty to manage asbestos on the dutyholder for non-domestic premises and the common parts of multi-occupancy domestic premises. Northern Ireland has its own, closely matching 2012 regulations, enforced by HSENI. The regulation requires a suitable and sufficient assessment of whether asbestos is or is liable to be present. It does not use the words "management survey": the survey is HSE's recommended way to carry out that assessment in most buildings.
When do you need an asbestos management survey?
You will usually need one if you are the dutyholder for non-domestic premises built or refurbished before 2000 and you have no reliable, current survey. HSE says that in most cases the duty to manage means arranging a management survey by a competent asbestos surveyor.
HSE's guidance is to assume there is asbestos in any building built or refurbished before 2000. Asbestos use in building work was banned in 1999; the year 2000 is HSE's rule of thumb for presumption, not a legal cut-off. Newer buildings are unlikely to contain asbestos in their fabric, but HSE points out that older plant and equipment can still contain it, for example oven seals and insulation, gaskets, electrical switchgear and heat-resistant panels.
Situations where a management survey is commonly needed:
- There is no survey at all for a pre-2000 building you are responsible for.
- You have taken on a building (a purchase, a new lease with repair obligations, or a new management contract) and the asbestos information you inherited is missing, partial or doesn't match the building.
- The existing survey is an old report that doesn't cover all buildings or areas, or has large "no access" sections that were never followed up.
- Parts of the building have changed since the last survey, for example new partitions, a reconfigured floor or areas brought back into use.
Is there an alternative? HSE's FAQ says the person responsible must either arrange a survey if ACMs may be present, or presume the worst case (that asbestos is widespread) and take full precautions for any work. HSE adds that it is often less troublesome and more proportionate to have a survey carried out. Presuming everything means every contractor treats every material as asbestos, which tends to slow down routine jobs.
Very simple premises. HSE says that if your premises are very simple, for example a building whose only asbestos is an asbestos cement roof with no hidden asbestos, you may be able to do your own inspection, taking care never to walk on fragile roofs. For anything more complex, it says you will need a competent surveyor.
Private homes are different. The regulation 4 duty does not apply inside private homes. It covers non-domestic premises and the common parts of blocks of flats and houses converted into flats, such as corridors, stairs, lift shafts, roof spaces and plant rooms.
What does the surveyor inspect in a management survey?
HSE says a management survey should inspect all rooms, corridors, stairs, basements and undercrofts; under floor coverings, ceiling voids, lofts, risers, service ducts and lift shafts; external areas including roofs, soffits, gutters and windows; and other areas maintenance could disturb, such as behind access hatches.
The scope is wider than many owners expect. HSG264 says all areas should be accessed and inspected as far as reasonably practicable, and HSE lists the areas a management survey should include:
Areas HSE expects a management survey to cover
- All rooms, corridors, stairs, basements, cellars, underground rooms and undercrofts.
- Under floor coverings, above false ceilings (ceiling voids), lofts, inside risers, service ducts and lift shafts.
- External areas, including roofs, soffits, gutters and windows.
- Other areas liable to be disturbed by maintenance, for example behind access hatches.
How intrusive is it? HSG264 says management surveys will often involve minor intrusive work and some disturbance: lifting ceiling tiles, opening hatches and panels, looking behind fascias and other surface materials. The extent depends on what disturbance foreseeable maintenance would cause, including the installation of new equipment and cabling. The guide says management surveys are only likely to involve simple tools such as screwdrivers and chisels. They do not involve breaking into the structure, opening up walls between floors or lifting structural floors: that is refurbishment or demolition survey territory.
Similar rooms. In buildings with many similar rooms, such as hotel bedrooms or office floors, HSG264 allows a survey strategy that reflects this, but it still says all rooms should be visually inspected. Ask how the surveyor will handle repeated room types before you accept a quote that inspects only a sample of them.
Plant and equipment. If you maintain older plant, boilers or machinery, tell the surveyor and agree whether it is in scope. HSE notes that maintenance may disturb asbestos in old equipment, and that if you don't know what equipment there is and where, a management survey is the way to find out.
Don't narrow the scope to save time. HSE warns that the value and usefulness of the survey can be seriously undermined if either you or the surveyor restrict its scope. HSG264 adds that restrictions lead to delays and make managing asbestos more complex and expensive later. A cheaper survey that leaves out the roof or the ceiling voids will usually just move the cost to the first maintenance job that needs to go there.
Will the surveyor take samples or presume materials contain asbestos?
Usually both. HSG264 says a management survey will usually involve sampling and analysis, but can also presume materials contain asbestos. Surveyors should always try to positively identify ACMs, and blanket ("default") presumption should be avoided where possible.
There are two ways a surveyor can deal with a suspect material:
- Sample it. A small piece is taken and sent for analysis. HSE says this is the only way to confirm whether a suspect material contains asbestos. Under regulation 21 of CAR 2012, anyone who asks for a sample to be analysed must use an analyst accredited as competent, and HSG264 says laboratories doing bulk analysis for others must be accredited by UKAS.
- Presume it. The surveyor records the material as containing asbestos (or, where there is good evidence, as not containing it) without a sample. A presumed material must still have its condition assessed.
HSG264 explains how the two work together. Samples should be taken from each type of suspect material. If a material is found to contain asbestos, other similar materials used the same way in the building can be "strongly presumed" to contain it too, so the surveyor doesn't need to sample every ceiling tile or every length of pipe. Materials that vary (different coatings, signs of repair) need more samples. Sampling can happen during the visit or, on some larger surveys, as a separate exercise afterwards.
Why HSE is cautious about presuming everything. HSG264 says presuming defers sampling until later, for example until just before work is done, but it has disadvantages:
- it is less rigorous, and harder to control;
- it can lead to constant obstructions and delays before work can start;
- any work on a presumed material has to be done by suitable contractors using methods that comply with CAR 2012, whether or not the material is actually asbestos;
- it can lead to unnecessary removal of non-asbestos materials and their disposal as asbestos waste, and the dutyholder bears those extra costs.
The guide says default presumption should only be used where the client asks for it and/or where access genuinely can't be obtained. It accepts that default presumption may suit some small or simple premises as part of the client's management arrangements. If a quote is noticeably cheaper because it presumes rather than samples, that is the trade-off you are accepting.
Some materials need sampling to rule out. HSG264 notes that textured coatings, paints and vinyl floor tiles may contain very fine asbestos that can't be seen by eye, so older examples have to be presumed unless they are sampled and analysed. It says that unless the surveyor has adequate evidence that a material is asbestos-free (plaster, plasterboard or wood, for example), it should be presumed or strongly presumed to be an ACM.
Sampling in an occupied building. Because sampling disturbs a small amount of material, HSG264 says a site-specific assessment and plan of work is required under CAR 2012. Practical arrangements, such as sampling only when a room is empty, labelling sample points and cleaning up, are agreed with you during planning.
What are the material assessment and priority assessment?
The material assessment, done by the surveyor, scores how readily each material would release fibres if disturbed. The priority assessment considers how likely it is to be disturbed. HSE says that even if the surveyor provides a priority assessment, the dutyholder must validate it, because only you know how the building is used.
HSG264 says a management survey should include a material assessment for every asbestos-containing, presumed or suspect material. This is one of the main differences from a refurbishment or demolition survey, which normally records only what and where, because the material is due to come out.
How the material assessment works. HSG264 gives a simple scoring method based on four factors:
| Factor | What it reflects |
|---|---|
| Product type | Some products (lagging, sprayed coatings) release fibres far more readily than others (asbestos cement, floor tiles). |
| Damage or deterioration | Material in good condition scores lower than material that is cracked, broken or crumbling. |
| Surface treatment | Sealed, painted or encapsulated surfaces score lower than unsealed ones. |
| Asbestos type | Taken from the analysis; presumed materials are scored as the highest type unless there is strong evidence otherwise. |
Each factor is scored and added up to give a total between 2 and 12. HSG264 bands the results: 10 or more is a high potential to release fibres if disturbed, 7 to 9 medium, 5 to 6 low, and 4 or less very low. Non-asbestos materials aren't scored.
One practical consequence: because presumed materials are scored as the highest-risk asbestos type, a material that is presumed rather than sampled will often score higher than it would after analysis. That is another reason HSE prefers sampling where it is practical.
The priority assessment is yours. A high material score does not automatically mean a material is the top priority for action. HSG264 says priority comes from a risk assessment that takes into account where the material is, how much of it there is, how the area is used and occupied, what activities happen there, and how often maintenance is likely. A damaged board in a locked, rarely visited plant room may matter less, day to day, than a lower-scoring material in a busy corridor where cables are regularly run.
The surveyor can help, especially in small or simple premises, but HSG264 says the priority assessment should only be done in consultation with the dutyholder, and HSE says you must validate any priority scores in the report.
What happens next. HSG264 says the combined scores are used to decide which materials need action and what action. Protecting or enclosing, sealing or encapsulating, or repairing should be considered first; removal is for where those aren't practical. HSE says materials in good condition that are unlikely to be disturbed are usually safer left in place and managed.
What happens to areas the surveyor can't get into?
Any area not accessed must be presumed to contain asbestos. HSG264 says these areas must be clearly stated in the report and managed on that basis: no maintenance or other disturbance work there until further checks are made.
Locked rooms, a tenant's unit that wasn't available, a roof without safe access, a riser behind a sealed panel: every survey can run into areas it can't reach. HSG264 is clear about what follows. Any area not accessed (and where no other information exists) must be presumed to contain asbestos, clearly identified in the report, and managed on that basis. In practice that means nobody drills, cuts, lifts or opens anything there until it has been inspected.
The guide also says how to keep these gaps to a minimum:
- Difficult areas, including locked rooms, should be identified with the dutyholder at the planning stage and access arranged, for example rooms unlocked, doors and corridors cleared, or a mobile elevating work platform for high areas.
- If there is no entry on the day, a revisit should be made when access is possible.
- If the surveyor can't get into an area during the survey, the dutyholder must be told as soon as possible so that later access can be arranged.
- Any restriction on scope must be agreed by both parties before work starts, documented, and fully justified.
Why this matters to you: each no-access area becomes a presumed-asbestos area in your register. A contractor asked to work there later will have to treat it as asbestos or wait for an inspection. A long list of "not accessed" areas often means a second visit sooner rather than later.
Watch for generic exclusions. HSG264 says excluded and inaccessible areas should be specific to the survey, with reasons, and not generic. A blanket line such as "voids not inspected", without saying which voids and why, deserves a question.
What's in a management survey report, and what does it feed?
HSG264 says the report should include an executive summary, the scope, site and survey information, results with material assessment scores and marked-up plans, conclusions and actions, and the laboratory results. You use it to build your asbestos register and management plan; the report itself is not the register.
HSG264 sets out the sections a survey report should contain:
- Executive summary: locations with identified or presumed asbestos, areas not accessed, materials with high material assessment scores, and clear notes on actions and priorities.
- Introduction: the scope, purpose and aims, and the age and construction of the buildings.
- General site and survey information: who surveyed and who commissioned it, the dates of the survey and report, areas included and excluded, the method and type of survey, and any variations or agreed exclusions.
- Survey results: a table and marked-up plans showing each material's location, extent, product type, whether it was presumed, strongly presumed or identified, and the asbestos type. For a management survey the table also gives accessibility, damage, surface treatment, the material assessment score or category and any actions.
- Conclusions and actions.
- Bulk analysis results from the laboratory.
Two smaller details are worth looking for. HSG264 says materials shown not to be asbestos should be recorded in a separate table, which helps settle future debates about them (HSE adds that noting non-asbestos materials that could be mistaken for asbestos prevents confusion). And photographs should be included: they show the material, its condition and surroundings, and give you a baseline for comparing condition over time.
From report to register. HSG264 says the survey report will generally not be the asbestos register. The register is a simpler, living document taken from the report: HSE's minimum contents are all known and presumed ACMs, their type, amount and condition (with dates of the original and last inspection), the material and priority assessments, and presumed locations where the surveyor couldn't get access. Ask for results in a format that can be lifted straight into a register, whether paper or electronic.
From register to plan. Regulation 4 then requires a written plan for managing the risk, which must be reviewed at regular intervals. HSE's guidance is to update the register at least once a year, through regular condition checks usually called re-inspections.
When isn't a management survey enough?
When work will disturb the building fabric in areas the management survey didn't open up. HSG264 says management surveys cover routine and simple maintenance; a refurbishment survey is needed for all work which disturbs the fabric where the management survey has not been intrusive.
A management survey is designed around normal occupation and routine maintenance. It looks into voids and behind panels, but it does not break into walls, floors or structural elements. So it can't tell you what is inside a partition you plan to remove or under a floor screed you plan to dig up.
HSG264 draws the line clearly. Management surveys should cover routine and simple maintenance work. Where more extensive maintenance or repair is involved, there may not be enough information in the management survey, and a localised refurbishment survey will be needed. A refurbishment survey is required for all work which disturbs the fabric of the building in areas where the management survey has not been intrusive. The guide says the dutyholder makes that decision, probably with help from others.
Examples of jobs that usually go beyond the management survey:
- removing or moving partitions and walls, or stripping out a kitchen, toilet block or fitted units;
- replacing a ceiling, a floor or a roof covering;
- opening up walls or floors for new services;
- removing or dismantling plant;
- any demolition.
This links to a separate legal duty. Under regulation 5 of CAR 2012, an employer must not carry out demolition, maintenance or other work that exposes or is liable to expose employees to asbestos unless it has assessed whether asbestos is present, or presumes it is and takes the precautions the regulations require.
Planning works soon? It is often sensible to tell the surveyor now. HSG264 says larger premises often need a mix of survey types, for example a management survey for most of the site and a refurbishment survey in the part due for work.
How should you prepare for an asbestos management survey?
Gather plans and past asbestos information, list every building and area in scope, arrange keys and access to roofs, voids, risers and plant rooms, and tell the surveyor about the building's use, hazards and any planned work. HSG264 says the key to an effective survey is the planning.
HSG264 is blunt that a survey "is not about just turning up and taking samples". It expects an exchange of information between you and the surveyor before the visit, ideally with a walk-through for larger or complex premises. Most of what goes wrong on the day, such as locked rooms, no roof access or missing plans, can be fixed beforehand.
- Decide what you need from the survey. HSG264 suggests the dutyholder considers why the survey is needed, what type is needed, what information it must provide and what format you want (a register-ready table, drawings, electronic or printed).
- Collect existing information. Building plans and drawings, previous asbestos surveys (including old Type 1, 2 or 3 reports), the current register, records of asbestos removal or repairs, and the health and safety file if there is one. HSE also suggests asking previous owners or tenants, any facilities management company, equipment suppliers and the original architect or builder.
- Define the scope precisely. List every building, outbuilding and external area. Mark it on a site plan if you can. Say whether the grounds and associated structures are included.
- Explain the building's history and use. When it was built, whether it has been extended or refurbished and when, what plant and equipment is installed, what activities happen in each area, and whether it is occupied or vacant.
- Arrange access. Keys for every locked room, cupboard and plant room; access to risers, service ducts and lift shafts; loft and ceiling-void access; and safe access to roofs and high areas (HSG264 mentions mobile elevating work platforms where needed). Name a contact who can open doors on the day.
- Flag hazards and permits. Site safety rules, permit-to-work systems, restricted or clean areas, machinery or lifts that need making safe, and who is responsible for isolating services.
- Plan around occupants. Agree survey times, especially for sampling in occupied rooms, and tell tenants and staff what to expect.
- Mention planned work. If works are coming, the surveyor may recommend a refurbishment survey for those areas instead of, or as well as, the management survey.
Choosing the surveyor. HSE strongly recommends using an accredited asbestos surveying organisation; UKAS is currently the sole recognised accreditation body in Great Britain for asbestos inspection bodies. Accreditation is not a legal requirement for surveyors, but HSG264 says the dutyholder should not appoint a surveyor unless they are competent.
How do you check a management survey report?
HSG264 Box 11 lists the checks: compare the report with what you ordered, look for unagreed caveats, confirm the survey type, check plans are clear and accurate, check all areas were accessed, and check sample numbers are sensible and cover variations in materials.
HSG264 says the client should examine the report and make sure the survey was adequate and the report is suitable and accurate. Its checklist (Box 11) is short enough to work through with the report open:
HSG264 Box 11: what the dutyholder should check
- Check the report against the original tender or quote.
- Check for unagreed caveats or disclaimers.
- Check the survey is the type requested: management, refurbishment/demolition, or a combination.
- Check diagrams and plans are clear and accurate.
- Check all rooms and areas have been accessed.
- Check enough samples have been taken (usually 1 to 2 per area or room) and that sample numbers aren't disproportionate, for example dominated by one type of material.
- Check sample numbers reflect variations in the same material, for example different ceiling tiles in the same room.
- Check for any obvious discrepancies and inconsistencies.
A few practical additions an owner or facilities manager can do quickly:
- Walk the plans. Take the marked-up plans round the building. Are room numbers right? Is anything missing, such as a store, a plant room or an outbuilding?
- Read the "not accessed" list. Each item is a presumed-asbestos area. Decide which ones you need to get inspected and book a revisit.
- Look at the presumptions. If much of the report is presumed rather than sampled, ask why, especially where it wasn't agreed in advance.
- Check the laboratory results are included and that the laboratory is UKAS-accredited.
- Raise questions in writing before you build your register from the report. Errors carried into the register tend to stay there.
Then turn the report into action: build or update your register, validate the priority assessment, update your management plan, and share the information with anyone who may work on the building fabric, including contractors at the quote stage.
Related guides
Asbestos management surveys: frequently asked questions
What is the difference between a management survey and a refurbishment and demolition survey?
A management survey is for buildings in normal use. It involves only minor intrusion with simple tools and includes a condition assessment of each material. A refurbishment or demolition survey is done before building work, is fully intrusive and destructive where necessary, and needs the area to be vacated and confirmed fit for reoccupation afterwards.
Is an asbestos management survey a legal requirement?
The law requires the dutyholder for non-domestic premises to make a suitable and sufficient assessment of whether asbestos is present and to manage it. It doesn't name a survey type, but HSE says that in most cases this means arranging a management survey by a competent surveyor. The alternative HSE describes is presuming asbestos is widespread and taking full precautions for any work.
Does my building need a management survey if it was built after 2000?
HSE says buildings built after 2000 are unlikely to contain asbestos in their fabric, so a survey is not usually needed for that reason. Older plant and equipment can still contain asbestos, for example gaskets, seals and electrical switchgear. If any part of the building is older or was refurbished before 2000, that part should be treated as a pre-2000 building.
Can we stay in the building during a management survey?
Usually, yes. A management survey is designed for buildings in normal use and, unlike a refurbishment or demolition survey, HSE's guidance doesn't require the area to be vacated. Sampling disturbs small amounts of material, so the surveyor will restrict entry to the sampling area and may ask for some rooms to be empty while samples are taken. Agree timings with the surveyor before the visit.
What does presumed mean in a survey report?
Presumed means the surveyor has recorded the material as containing asbestos without a laboratory result. Strongly presumed usually means a similar material elsewhere in the building was sampled and found to contain asbestos. Presumed materials must be managed as asbestos until a sample shows otherwise.
What happens if the surveyor couldn't get into some rooms?
Those areas must be presumed to contain asbestos and should be listed specifically in the report. Nobody should carry out maintenance or other disturbance work there until they are checked. Arrange access and book a revisit so the gaps can be closed.
Is the survey report the same as an asbestos register?
No. HSE's survey guide says the report will generally not be the register. The register is a simpler, living document taken from the report, listing known and presumed asbestos, its condition and the assessments, and it is updated as things change.
Who works out the priority assessment?
The surveyor scores how readily each material would release fibres, which is the material assessment. The priority assessment, how likely each material is to be disturbed, depends on how the building is used. HSE says the dutyholder must validate any priority assessment in the report, because only they know what happens in the building.
Can I use our management survey before refurbishment work?
Only for areas where the survey was intrusive enough for the work planned. HSE's survey guide says a refurbishment survey is required for any work that disturbs the building fabric where the management survey was not intrusive. Discuss planned works with a surveyor early so the right survey is done in time.
Does a surveyor have to be UKAS-accredited?
Not by law, but HSE strongly recommends using an accredited asbestos surveying organisation, and UKAS is the recognised accreditation body for asbestos inspection bodies in Great Britain. Whoever surveys must be competent. Laboratories analysing samples must be accredited, which is a legal requirement.
Sources
We checked the facts on this page against these sources on 14 November 2026: